Can anyone comment on RSP redundancy with SSO mode?
I have a test 7507 with rsp-k4pv-mz.120-32.S8.bin on both RSP2s. I've done

R0 10021901 12.2(33r)XND. F0 07091401 12.2(33r)XNC. F1 07091401 12.2(33r)XNC.Sep 15 03:27:20.681:%IOSXEOIR-6-ONLINECARD: Card (fp) online in slot F0. CARRR01#sh platform. Chassis type: ASR1006. Slot Type State Insert time (ago)- - - -0 ASR1000-SIP10 ok 2w0d. 0/0 SPA-5X1GE-V2 ok 2w0d. 1 ASR1000-SIP10 ok 2w0d. R0 ASR1000-RP2 ok. Reload the Cisco WebEx Node SPA using the hw-module subslot reload command. Router# show platform software process slot r0 monitor cycles 4 interval 3 top - 18:26. Eg:%CMRP-3-CHASSISMONITORONLINETIMEEXCEEDED: R0/0: cmand: Reloading slot because it has failed to come online Conditions: The module that's failing to boot may have been newly inserted and may have not been upgraded to ROMMON version 16.2(1r) to be consistent with other cards in the router chassis. This older ROMMON will not be.

this:

1. Cheat Tables for yuzu. Contribute to zarroboogs/yuzu-ct development by creating an account on GitHub.
2. Hw-module module. The CLI will only give you the further option of 'shutdown' if the service module supports it eg. An FWSM does support shutdown so you would get the option in the above command. A CSM does not support shutdown so you would only get the option to reload.

service single-slot-reload-enable
redundancy
no keepalive-enable
mode sso
And it doesn't seem to ever sync the slave
ranttest#show red
Redundant System Information :
------------------------------
Available system uptime = 14 minutes, 49 seconds
Switchovers system experienced = 0
Standby failures = 0
Last switchover reason = none
Hardware Mode = Duplex
Configured Redundancy Mode = sso

Hw-module Slot R0 Reloadable

Operating Redundancy Mode = hsa
Maintenance Mode = Disabled
Communications = Down Reason: Simplex mode
Current Processor Information :
-------------------------------
Active Location = slot 2
Current Software state = ACTIVE
Uptime in current state = 13 minutes, 24 seconds

Hw-module Slot R0 Reloaded

Image Version = Cisco Internetwork Operating System
Software
IOS (tm) RSP Software (RSP-K4PV-M), Version 12.0(32)S8, RELEASE SOFTWARE
(fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2007 by cisco Systems, Inc.

Hw-module Slot R0 Reloading

Compiled Mon 20-Aug-07 16:34 by leccese
BOOT =
CONFIG_FILE =
BOOTLDR =
Configuration register = 0x2102
Peer (slot: 3) information is not available because it is in 'DISABLED'
state
ranttest#redundancy force-switchover
Cannot perform switchover until the standby is fully initialized.
The box is up, its got two OSPF adjacencies, maybe a hundred routes - its
not doing anything fancy, so I'm kind of stuck here. The production target
is 7507s /w RSP4s, the same OSPF, and about 180k routes via BGP. Any idea
what might be wrong here?
_______________________________________________
cisco-nsp mailing list cisco-nsp@puck.nether.net

Hw-module Slot R0 Reloader

https://puck.nether.net/mailman/listinfo/cisco-nsp
archive at http://puck.nether.net/pipermail/cisco-nsp/